![]() So, it can be anything you think of relevant or non-relevant. Siri no longer gets caught up in a low A.I. ![]() Siri will say: "OK, just tell me what you want to be reminded about." "Remind me EVERYDAY when it's 12 O'clock A.M." You'll be doing this with Siri and the "Reminder" app, which comes FREE with the iPhone.ġ) Hold down the center home button and say: I don't own a iPh6, but it should be the same. Tested on: iPh5 and two iPh4 Note: Siri does not work on iPh4, but linked devices automatically carry over information if spoken through the iPh5. And you can further tweak it so it doesn't block or lock up your phone when you are being alerted of the passing hour.ġ) Using SIRI to set up a DAILY reminder that alerts you every hour and repeats INDEFINITELY.Ģ) Just alerts you of the passing hour with no other intrusive notifications.ģ) Brain hack for the neurotic: Choosing a ringtone that is soothing or has a positive association. Really appreciate your help, I'm unsuccessfully trying for days now.YES, you can setup an hourly chime on an iPhone WITHOUT downloading an app or any Jail Breaking for FREE! With just using sounds already on your phone, or any custom tone you create. at 16:00:00, 17:00:00.ĪLRM1_MATCH_MIN_SEC 0b1100 // when minutes and seconds match orĪLRM2_MATCH_MIN 0b110 // when minutes matchĪnd how to I get only one of two Alarm running? In the end, I just want to trigger the interrupt once every hour, e.g. How long should the LOW signal from the SQW pin usually be? Pin still stays low after the first interrupt, ist there anything else I have to change? clear A1F/A2F flags for previously set alarmsīut I am not 100% sure if this was right because actually nothing really changed. WriteControlByte(temp_buffer, 0) //Modification from I changed the code in DS3231.cpp to this : There are multiple get methods which allow you to get the time from your rtc, then add 30s and set alarm 1 again. If you want to trigger an alarm after 30 seconds, you need to set the time again. The example just triggers once at a defined time. Reply to this email directly, view it on GitHub, or mute the thread.Īhh OK, that's a completely new use case. You are receiving this because you commented. If you want to sleep again, you'll need to either powerDown again in wakeUp or the loop.ĭid you change the Times that are configured here? Afterwards the Arduino is awake and will run the loop. In my example, you let the arduino sleep and then wakeUp is called. Therefore it will run after setup (see arduino docs: ) The loop function is the one, that is automatically run when the arduino is awake. loop is started once the device wakes up again powerDown(SLEEP_FOREVER, ADC_OFF, BOD_OFF) checkAlarmEnabled( 2)) ĪttachInterrupt( digitalPinToInterrupt(wakeUpPin), wakeUp, FALLING) setA2Time( 0, 0, 30, ALARM_BITS, false, false, false) tA2Time(Day, Hour, Minute, AlarmBits, DayOfWeek, 12 hour mode, PM)Ĭlock. setA1Time( 0, 0, 0, 0, ALARM_BITS, false, false, false) tA1Time(Day, Hour, Minute, Second, AlarmBits, DayOfWeek, 12 hour mode, PM)Ĭlock. This is the interesting part which sets the AlarmBits and configures, when the Alarm be triggeredīyte ALRM1_SET = ALRM1_MATCH_MIN_SEC // trigger A1 when minute and second matchīyte ALRM2_SET = ALRM2_MATCH_MIN // trigger A2 when minute matches (and second is 0 as A2 does not support seconds) # define ALRM2_MATCH_HR_MIN 0b100 // when hours and minutes match # define ALRM2_MATCH_MIN 0b110 // when minutes match # define ALRM2_ONCE_PER_MIN 0b111 // once per minute (00 seconds of every minute) # define ALRM1_MATCH_HR_MIN_SEC 0b1000 // when hours, minutes, and seconds match # define ALRM1_MATCH_MIN_SEC 0b1100 // when minutes and seconds match # define ALRM1_MATCH_SEC 0b1110 // when seconds match # define ALRM1_MATCH_EVERY_SEC 0b1111 // once a second They need to be combined into a single value (see below) Those are the ALARM Bits that can be used * Sets an alarm using a DS3231 device, goes to sleep and wakes up again
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |